Albrektsen User

UPVC Door Hinge Repair

Misaligned upvc doors are a common problem that can often be easily corrected by changing the hinges. Firstly locate the adjustment screw on the door side of the hinge. It is usually located on the top or bottom of the hinge and can be turned clockwise to raise it or anti-clockwise to lower.

Butt Hinges

Hinges are crucial to a door's performance and security, however when they begin to rust or get worn, they may fail, making doors difficult or even impossible to open. There are many different types of hinges, and they can be easily repaired or replaced. It is important to repair a minor issue or replace the entire hinge.

The full mortise, the half surface and the concealed hinges are offered in different designs to suit the wide range of door sizes, widths and thicknesses. They are available in two-knuckle styles and three-knuckle designs, as well as five-knuckle styles, and swing-clear designs. There are also designs for electrical security, heavy-duty hinges and non-removable pins (NRP).

A hinge that is lubricated makes it easier to use and reduces the amount of friction caused by repeated use. You can lubricate the hinges using dry or liquid oils, such as petroleum jelly, cooking oil paraffin wax, or furniture polish. Apply a thin layer grease on the barrel of your hinge and let it soak for at least 15 minutes.

If your hinges are rusty or are stuck, you will have to clean the barrel and remove the pin. After doing this clean the hinge barrel with a wirebrush as well as some penetrating oils like Liquid Wrench or the PB Blaster or Liquid Wrench. After cleaning the barrel, put it back on the hinge and test it to ensure that the pin fits properly.

One of the most common causes of a hinge that is loose are stripped screw holes. It can be difficult to tighten screws using stripped holes. To fix the damaged screw holes, cut a dowel from wood into pieces of 1 inch and then drill them into the stripped hole. Spread carpenter's glue onto the dowel, and tap it in place using the Hammer.

A worn hinge pin is another frequent cause of loose latches. The best solution to repair a damaged hinge is to replace the pin. You can buy new hinge pins from hardware stores or online. Once you've bought the replacement hinge pin, you can install it by getting rid of the old pin before placing the new pin in the hinge barrel.

Rebated Hinges

Rebated hinges are a popular choice for doors that need to be positioned inside frame doors which have been constructed around them. The hinges are set within the frame to ensure they don't encroach on the door sash while they are open. They are then fixed onto the edges of the door. They can be fitted on uPVC aluminum, timber and aluminium doors. They are available in different sizes to accommodate various door sash dimensions.

These hinges are a great solution for doors that require more adjustability than traditional butt hinges provide. They are a great choice for doors with chamfer features that don't allow the use of traditional butt hinges. They come with a dust cap made of metal and are adjustable in 3 planes and can support up to 60kg per pair. They are simple to install and are suitable for right - or left-hand doors RH/LH.

Spraying an aerosol silicone or lithium grease on your rebated door hinges will fix the problem quickly and easily. It will stop the squeaking temporarily, but it is not a long-term solution. It will fade over time.

An alternative that is more durable is to drill the screw holes and fill them with wood filler. This will ensure that the screws are tight and you get a good grip on the door. You can also use toothpicks to strengthen the holes.

A dowel of wood the same size as the screw hole you have is an alternative. Make the hole enough to accommodate the dowel, put glue on the dowel and chisel it flush once the dowel is fixed. You can then fix the hinge back into place.

I have some old doors that have had the hinge recesses drilled too far and splinted. The frames are in an old building and are quite big, so replacing them is not an option. Could it be feasible to cut the frame's section and then splice a new block of wood, into which a new hinge recess could be made that will better hold screws for the hinges? Would this be an excellent idea? If so, in the event that it is what kind of wood is the best for this type of repair?

Flag Hinges

UPVC hinges can be used to upgrade or replace hinges currently in use. Many of the modern uPVC door models have adjustable slimline hinges. These hinges allow doors to be opened and closed easily and are more resistant to heat. These hinges require less maintenance and are less prone than older hinges to be draughty. Like all hinges they wear out over time and require adjusting.

If your uPVC door isn't closing properly, it could be due to the door's frame isn't at an appropriate level. It is essential to level the frame before you adjust the hinges. If you do not do this, the latch will not catch onto the strikeplate and the door will not close.

You can adjust a butt-type hinge by loosening the grub screw located in the middle of the hinge (face-on). Then, you can turn the top or bottom screws to allow an upward movement. To access a compression screw located on the top of the device, you'll need to remove the cap. This screw can be used to adjust the height of the hinge, with a a tolerance of up to 2 millimeters.

Flag hinges are more adaptable than butt hinges and can be adjusted both vertically and lateraly. local upvc door repairs Repair My Windows And Doors are less prone to draughts as they have smaller lip on the hinge. They are commonly found on older uPVC doors and can be replaced with modern T hinges.

Repairing hinges that are flagged by using wood glue or wood filler to plug any gaps in the hinge. After the filler has dried completely, sand it down and then paint the area. If you're not sure what kind of filler to apply, you can contact the store where you bought your hardware for advice. You can also choose a filler with more gloss to give the door a more polished appearance. You can also cover the gap with wood veneer. This option may be slightly more expensive, however it will make your door appear brand new.

Recess Hinges

Using a chisel, cut a shallow recess on the outside of the door frame. This will be the same size as the hinge you're installing. After you've made the required cut, scrape away the wood you've removed and then clean the area with a damp towel to ensure that the new hinge will rest perfectly against the surface of the frame.

After you've cleaned the area, screw in your new hinges and test to see how the door works. Make sure that the sash joins the frame on both the top and bottom and that it doesn't have any gaps or catch on the hinge at any point, as this could indicate that your uPVC door isn't in alignment and must be adjusted.

You can buy a spirit level at most hardware stores for reasonable prices. Simply place the level on the top of the door and observe if there are any differences in height between the frame and the door, this is an indication that the hinges need to be adjusted.

You can adjust uPVC hinges by using an Allen key on the door side of the hinge and turning clockwise to tighten (lift) or anti-clockwise to loosen (lower). Repeat this procedure until the door closes and opens smoothly with no creaking sounds.


There are three types of uPVC hinges; Butt, Flag and Rebated. Each hinge type has distinct advantages and disadvantages, so be certain to research them thoroughly before making your final choice. But, no matter which hinge you select it is important to know how to maintain and repair your uPVC doors in order to keep them looking good and operating effectively for a long time.

Check out our guide on how to recognize the type of uPVC uPVC is on your door and how to adjust it. We've also provided the steps needed to adjust each type of hinge to allow you to jump to the one you require!

Member since: Sunday, September 15, 2024

Website: https://www.repairmywindowsanddoors.co.uk/macclesfield-upvc-door-repairs-near-me/