Kornum User

Reasons to Change Door Lock

You can alter your door lock for many reasons, from improving the security of your house to redecorating the entrance. You may also need to change locks if your key is stuck in the lock or is difficult to turn.

The process of changing your lock is a simple project that even novice DIY homeowners can complete. To start, gather the materials you need.

Remove the old lock

Removal of the old lock from the door is an essential step before installing the new lock. This is particularly important in the event that you suspect someone else has access to your home. This is an excellent idea after you've moved into your new house, had a break-in, or welcomed a roommate. The process is much easier than you might think and can be completed within just a few minutes.

Begin by removing the screws that hold the deadbolt faceplate on the door frame. To remove the faceplate, you'll need to remove screws on both sides. This will let you observe what's behind it and will give you a better understanding of what to do with the rest of the steps.

After removing the old faceplate, you must take off the bolt along with the strike plate and strike plate. Use a screwdriver or a wrench to loosen the bolt and take it out of the hole in the door. If the bolt is rusted, you may have to use a chisel and hit it. When using a chisel to remove the bolt, be careful not damage the door frame.

Before you take down the lock that was previously in use, make sure that your new deadbolt and doorknob will fit into the existing holes in the door. Most hardware stores and big box stores carry different kinds of locks. They can assist you in choosing the best one to meet your needs. If the lock you bought is not compatible with your door, bring it back and seek help.

While you are removing the lock that was previously in use, look for small slits or depressions in the handle or around the trim. If you are able to locate them, use a straightened safety-pin or a flat screwdriver to open the handle.

Once the screw inside the handle is removed, you can begin removing the knob from its spindle. To do this, locate the set screw at the knob's base and loosen it. Then, take the spindle off.

Install the new lock

It's a good idea to change locks on doors throughout your home periodically, especially after a burglary or when you move into a room with roommates. Change the lock is an affordable, simple and effective method to ensure that your home is safe. With a screwdriver and a few simple instructions most people can do it by themselves. You might also want to know how to change the key on your door lock to ensure that only you have the key.

You'll need to purchase an additional lock that has the same keyway as your existing lock. Many locksmiths will change the lock's key for a fee, but you can save money by doing it yourself. You can buy a new lock at a hardware store, or on the internet. A standard deadbolt will usually fit on all doors however, you'll have to measure the size of your door to ensure that it fits.

The majority of the time the lock you purchase will be supplied with the cardboard template that will show you how it will fit on the door. This template can be used to drill the hole. It is much easier than having to measure every time. If the template does not match your hole, take it back to the shop and request a replacement.

You must install the new lock on the right side of the door. You can check this by looking at the latch, which ought to be marked "up" or something similar. Make sure the latch is properly seated in the plate and then attach it using the supplied screws.


When replacing a knob lock it is important to be aware of the handing. Some knob locks are right-handed. If you are not careful, the knob could be installed on the wrong side of your door, which would prevent it from being locked from the inside or outside.

After you've finished, you should test your new lock to confirm that it's working. It should be able to lock and unlock the door with keys from inside as well as the outside. If you aren't satisfied with the result, you can call a locksmith to repair the issue.

Test the lock

If a lock on your door isn't able to be opened can be a nuisance and can be dangerous, it could also put your family's safety at risk. It's easy to solve the majority of door lock problems by conducting some troubleshooting and lubrication. First, make sure that your key is correctly cut and that the lock assembly itself isn't loose or dirty. If this doesn't solve the issue Try lubricating the door lock actuator with graphite powdered with powder.

Check that the doorlock switch, wiring harnesses and actuator connector all work correctly. Check the wiring diagram or manual to determine the color-coding and function of the wires for each door lock switch. Use a test light or digital meter to determine if the door lock actuator receives power and ground when the switches are turned on. If you can see voltage toggles with each switch it means that the switches are in good shape and the actuator will require replacement.

If the switch seems to work but the actuator doesn't move when you turn the knob it could be an issue with the actuator cylinder itself. The actuator cylinder is outfitted with pins that have a spring-loaded. They prevent the cylinder from turning until the key is put in, which then pushes them upwards to meet the height of the key at that location. Eventually, this causes the cylinder to spin and unlock the lock body and allow the handle to latch.

If the door lock actuator still not functioning, you can remove it by using a small screwdriver. You will need to remove the locking bolt first and then separate the plastic cover which holds the electrical connector. After that, disconnect the door lock actuator, and let it fall. You should be able to locate the two bolts of 10mm that hold the actuator in place and then remove them. Once the actuator is removed, you should be able to disconnect the black electrical connector and remove it along with the actuator and lock assembly.

Replace the key

If your deadbolt that is keyed or door knob is not functioning, you'll have to reset it or replace it. It's not hard to do it yourself and can save lots of money. It is recommended to have an expert locksmith examine the locks for any problems prior to beginning. This will give you peace of mind knowing that your home is secure and safe.

To begin, take off the exterior faceplate from the deadbolt or doorknob. There may be screws holding it in place, if so use a screwdriver to loosen them, and then pull the faceplate off. Then utilize a flat head screwdriver to take off the interior faceplate. After removing the faceplate you can take the bolt and screw from the lock cylinder.

A locksmith can tell you whether you need to replace or rekey your lock. They can also give you advice on the best security solutions for your home. They will also make any necessary modifications to the door and frame to ensure a perfect fit. They will also offer a warranty on their work.

If you choose to rekey your lock, you'll have to first buy a new key for it. window lock replacement is crucial to select a lock key that is fitted snugly. Using an incorrect key could cause damage to the mechanism's internal mechanisms and prevent it from functioning. To determine the size of a key, insert it into the lock. If the key fits completely against the plug then it's the right size. If the pins protrude out of the top of the plug, they're not long.

You may want to replace your door lock for a variety of reasons, including:

If you're moving into a previous owner's home or if you lose keys, rekeying the lock is an economical alternative than replacing it. It is also less invasive than a complete replacement. Rekeying an existing lock might not be feasible in certain situations. If the lock has been damaged or repeatedly jammed, for instance, it may be the right time to replace it.

Member since: Saturday, September 21, 2024

Website: https://www.repairmywindowsanddoors.co.uk/poole-window-lock-repairs-near-me/